Promoção* -58%
Promoção
*Campanha com início em 03-03-2024 e duração até 31-03-2024

PLA The Original ( Carbon Fiber Composite ) 50g ( Amostra ) - ProtoPasta

3.49 

(69.80  / kg)

Em stock

Envio:
🚚💨 Envio 24h
Prazo de entrega estimado para Portugal continental 1 a 3 dias úteis
Encomenda dentro de 20 horas 30 minutos (Até às 14:00)
para receberes já a partir de Segunda-Feira.
Porquê comprar na Evolt?
⚙️ Perfis & Settings de impressão: ProtoPasta
Nesta compra desbloqueias acesso à base de dados de perfis & settings de Impressão ProtoPasta
🔧 Em construção 🔧
⚡ Envio rápido (24h) produtos em Portugal
Loja Nacional com produtos em Portugal. Disponibilizamos de envios 24h para produtos "Recebe amanhã". Os pedidos realizados antes das 14h são enviados no mesmo dia.
🤗 Apoio técnico, ajuda e atendimento personalizado
Na Evolt investimos na tua satisfação e sucesso.

Somos uma equipa jovem com sede em Aveiro e estamos profissionalmente na indústria da Impressão 3D há 8 anos. Estamos aqui para fazer uma parceria contigo e ajudar-te em todas as etapas da tua jornada.

Prestamos suporte gratuito e rápido por telefone, chat e email, tu e a tua satisfação são a nossa prioridade.
Precisas de ajuda? Contacta-nos!
🛡️ Garantia de satisfação: Não consegues imprimir? Devolvemos o dinheiro
Aquilo que tens que saber antes de comprar com a Evolt.
É simples. Caso não consigas imprimir ou não gostes do filamento 3D devolvemos-te o dinheiro correspondente ao que ainda não usaste.
🧡 Acesso à Família Evolt: descontos, ofertas e oportunidades exclusivas para clientes Evolt.
🎮 Recebes 34 pontos por este produto
Com os pontos sobes de nível e desbloqueias acesso a descontos exclusivos.
💳 Ganhas 3 créditos por este produto
Créditos acumulam-se na tua carteira Evolt e podes usá-los como descontos em compras futuras!
📃 Descrição
⭐ Opiniões (0)

ProtoPasta é uma empresa situada nos Estados Unidos da América, de produção de filamentos para impressão 3D de alta qualidade.
Caracterizada pelos rolos feitos em cartão, esta marca é mundialmente famosa  por ser especializada em materiais como PLA e ABS modificados com outros materiais, como o PLA Magnético; o PLA Condutivo; PLA de fibra de carbono; HTPLA de cobre, latão ou bronze; ou o ABS-PC.


 

The original is still the best! World's First Carbon Fiber PLA filament was kickstarted by ProtoPlant nearly 5 years ago.

Others try, but can't match the quality and ease of printing experience afforded by this product.

Available at a cost low enough for everyday printing, try a mammoth 3kg spool for large format printing!

1.75mm diameter 3kg spools contain more than 1 km of filament!  How cool is that?!?!

 

 

 

 

We Started a Trend with the Original Easy Printing Exotic!

Protopasta Carbon Fiber PLA is based on our easy printing, high quality PLA. Made from the highest quality, dry ingredients and extruded with care in our Washington facility on our own purpose-built extrusion systems. CFPLA prints are demonstrably more rigid with easy processing (often using standard PLA settings) and support removal.  Excellent layer adhesion and minimal warpage even without a heated bed make this a great everyday exotic for accurate parts. Layer lines disappear with the beautiful matte black finish.  Also has a slight sheen due to the embedded carbon making it very photogenic!

**This filament is slightly more abrasive than standard PLA. Be prepared to replace your nozzle and do 1st layer adjustment after prolonged use or upgrade to a wear resistant nozzle for less maintenance.

  • Available in 1.75 & 2.85 (3) mm diameters.
  • 50g is on a 8" diameter spool & 3kg is on a 12" diameter spool.
  • Usable on most PLA-compatible printers, such as Lulzbot, Makerbot, FlashForge, Dremel, Ultimaker, Printrbot, and more!

In filament form, CFPLA is slightly more brittle than standard PLA, and requires extra care when handling. 

Processing is comparable to standard PLA. No heated bed required. Process may be less consistent on smaller nozzles and/or bowden type machines,

We frequently print using direct-drive systems with 0.4mm nozzles and print as high as 240C, though suggest 0.6mm and 210-230C for the best experience.

 

 

Getting Started with Proto-pasta PLAs including HTPLA

We've created this page to bring you a premium PLA and HTPLA printing experience that rivals our premium material. Follow below to improve your 3D printing experience. In other words, here's your shortcut to awesomeness with pasta. If at the end of this document you have questions or need assistance, please contact us at [email protected].

Filament Handling

Loose coils can be very tricky to manage. Going cowboy on your spool handling can quickly end up in a frustrating, tangled mess. Keep your loose coils wrangled with a spool holder like masterspool for a more trouble-free experience. Find out more about loose coil handling in Keith's blog post.

And for spooled filament, never let go of the loose end. When not in the printer extruder, tuck it away in the cardboard spool's corrugation! Also, avoid sharp bends and excessive force when loading filament into your printer.

Print settings

At Proto-pasta, we make high quality filament. We aspire to make exceptional results easy, but a positive result is very much dependent on your hardware, set-up, adjustments, and process parameters. Matching hardware with process and material for a positive experience is not always straight-forward, but you can start by pairing the following settings with your printer for a good starting point, then tune or troubleshoot as required.

Example settings for typical printer

  • Nozzle size = 0.4 mm (Standard to most printers & balances detail with productivity.)
  • Extrusion width = 0.45 mm (Typically larger than nozzle size. If using a larger nozzle diameter, be sure to set the extrusion width larger than that nozzle diameter.)
  • Layer thickness = 0.15 mm (For a balance of speed, quality & reliability.)
  • Speed(s) = 15-45 mm/s (Respecting mechanical and volume flow limits. Stay within the recommended speed range but apply slower speeds to the walls and faster speeds to the infill.)
  • Volume flow rate(s) = 1-3 cu mm/s (The result of above speed range, width, and layer thickness. Respect hardware and geometry limitations.)
  • Typical temperature = 215 C +/- 10 C (Matching material, hardware, and volume flow rate.)

Volume flow rate together with temperature dictates how melted the material is. This is hardware & condition dependent based on hot end, nozzle & extruder type, material & manufacturer as well as layer fan type, position & settings. Extrusion width, layer thickness & speed changes affect volume flow which may change required/desired temperature.

Additional settings of note

  • “Grid” infill type at 20-30% - “connect infill lines” unchecked (off).
  • Minimum 3 shells & 4 top/bottom layers for good surface quality.
  • Layer fan set to cool enough for build rate, but not so aggressive as to fail process by over-cooling nozzle and heater block.

Validation and fine-tuning

Post your prints & tag us @Proto_pasta on Twitter and InstagramNeed more help? Consider typical pitfalls and fixes below.

Typical pitfalls

  • Exceeding hardware capabilities.
  • Mismatch of flow rate and temperature.
  • Excessive nozzle cooling from layer fan yielding lower heater block and/or nozzle temperatures than set point.
  • Hardware shortcomings such as MK3 heat break, poor nozzle diameter, or other hangups.
  • Poor assembly or adjustment of components.
  • Excessive retraction distance or number of retractions.
  • Inaccurate flow with missing cross-sections or wall thickness not matching extrusion width software setting.

Typical Fixes

  • Heat break replacement with OEM, straight-through design and defect-free, smooth bore.
  • Proper assembly of components without plastic oozing gaps & with thermal grease.
  • Lightly oiling filament, but careful, a little goes a long way.
  • Reducing layer fan speed and/or isolating from heater block and nozzle.
  • Installing heater block sock to isolate heater block & nozzle from layer fan.
  • Increasing temperature to flow past internal hang-ups.
  • Reduce speed and/or choose a single speed for a single volume flow
  • Consider drive gear tension adjustment, bowden tube coupling/replacement, and spool mounting

We visited Joel and ended up with a helpful video on the subject:

 

Carbon Fiber PLA

Carbon Fiber Reinforced PLA

Our most popular exotic material, prints made with our Carbon Fiber PLA are demonstrably more rigid, providing excellent structural strength and layer adhesion with very low warpage. It has a beautiful matte black finish with a slight sheen due to the embedded carbon.

What is it made out of?

Protopasta Carbon Fiber PLA is made from NatureWorks 4043D PLA Resin compounded with 15% (by weight) chopped Carbon Fibers. It is more brittle than standard PLA in its filament form, so handle it carefully to prevent breakage.
How much stronger is it?
The short answer is that this filament isn't "stronger," rather, it is more rigid. Increased rigidity from the carbon fiber means increased structural support but decreased flexibility, making our Carbon Fiber PLA an ideal material for frames, supports, shells, propellers, tools... really anything not expected (or desired) to bend. It is particularly loved by drone builders and and RC hobbyists.
Print Settings

Because of the chopped carbon, Protopasta Carbon Fiber PLA may have trouble getting through smaller nozzles. We have had good success using a .5mm nozzle and direct-drive spring loaded pinch-roll style extrusion head.Generally, our customers find it prints just like standard PLA on their machines (at around 195-210° F), though others find success running it a bit hotter (around 220° F). Experiment with your printer and see what works best for you.

Density:
1.3 g/cm3 (1300 kg/m3)Parameters:
Bed Temp (if available, is not required): 50° C
Hot End Temp: 195 – 220° C

Carbon fiber and your printer nozzle

The carbon fibers in our filament are processed for an optimum size: short enough to print in PLA without clogging nozzles, but long enough to provide the added rigidity carbon fiber is famous for. At this length, the chopped carbon fiber makes this filament more abrasive than standard PLA. Prolonged use may result in more wear on your 3D printer, particularly lower-end nozzles.

 

 

 

Para uma correcta manutenção da sua impressora 3D, recomendamos sempre que trocar de material de filamento 3D,  a efectuar uma purga com filamento especial de limpeza.
Desta forma garante que não ficam vestígios de material nas paredes do nozzle, evitando o acumular de crosta que é criado sempre que efectua trocas de material.
Com este produto evita problema como "clogs" e "jams" e fará com que o seu nozzle mantenha-se sempre limpo, durando muito mais tempo.
Poderá encontrar a partir de 1.49€  no seguinte LINK

 

Este  material é altamente abrasivo. Recomendamos a utilização de Nozzles de aço endurecido.

Poderá encontrar  no seguinte LINK

 

 

3D lac comprar em Portugal

Para obter maior aderência à superfície da sua  impressora 3D recomendamos a aplicar 3DLAC  na base da plataforma.

Poderá encontrar no seguinte LINK

 

 

Este material é altamente higroscópico, absorvendo rapidamente a humidade do ar passados poucos minutos após aberto, impossibilitando desta forma a correcta impressão 3D do mesmo. O resultado das impressões 3D de materiais com humidade tendem a ser frágeis e de acabamento irregular ou em certos casos, torna-se simplesmente impossíveis de imprimir.
Deverá de usar soluções de caixas fechadas com dessecante como sílica ou caixas próprias secadoras de filamento.
Poderá encontrar  no seguinte LINK

 

 

Download:
Technical and Safety Data Sheet

 

50g- Rolo
PLA The Original ( Carbon Fiber Composite )
- Cor
1.75mm (+-0.05mm)
- Espessura / Tolerância de diâmetro
Fácil
- Facilidade de Impressão




⭐ Opiniões

Customer reviews

0.00
Based on 0 reviews
5
0%
4
0%
3
0%
2
0%
1
0%
Write Your Review
Add your review

Only logged in customers who have purchased this product may leave a review.

Informação adicional

Peso 0.15 kg
Marca

Cor

Preto

Peso

Amostra, 50 g

Diâmetro do Filamento 3D

1.75 mm

PLA The Original ( Carbon Fiber Composite ) 50g ( Amostra ) - ProtoPasta
🚚💨 Envio 24h

3.49 

Em stock

A nossa missão
Facilitar-te o acesso a produtos seleccionados com o rácio mais justo de qualidade/custo. Colocá-los ao teu dispor a um preço ainda melhor e tudo isto com stock em Portugal para que recebas os produtos o mais imediatamente possível
Links úteis
BlogTermos e Condições
Política de PrivacidadePolítica de CookiesRGPDResolução Alternativa de LitígiosTrabalha Connosco!
Levantamento em mãos
Dispomos da possibilidade de levantar gratuitamente encomendas nos Pickup 24/7.
Não dispomos de loja física.
Todas as compras de levantamento têm que ser previamente feitas online.
Obrigado pela compreensão!
Contactos
Largo Asilo da Gandarinha, nº 128
3720-362 Vila de Cucujães
Oliveira de Azeméis
Socialização faz bem
❤ Evolt 
2024
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram