Aviso COVID-19: Est√£o a ocorrer atrasos por parte das transportadoras, podendo em certos casos o transporte 24h alargar-se para 72h+

HTPLA Black ( Carbon Fiber Composite ) 50g ( Amostra ) - ProtoPasta

Em stock (pode ser encomendado sem stock)

8.95 

Em stock (pode ser encomendado sem stock)

Em stock (pode ser encomendado sem stock)

Envio:
Envio 24h
Prazo de entrega estimado para Portugal continental
Encomenda dentro de 5 minutos (Até às 14:00)
para receberes j√° a partir de amanh√£
Garantia
2
14 dias
devolução
Pagamento
seguro
Descrição:

ProtoPasta é uma empresa situada nos Estados Unidos da América, de produção de filamentos para impressão 3D de alta qualidade.
Caracterizada pelos rolos feitos em cartão, esta marca é mundialmente famosa  por ser especializada em materiais como PLA e ABS modificados com outros materiais, como o PLA Magnético; o PLA Condutivo; PLA de fibra de carbono; HTPLA de cobre, latão ou bronze; ou o ABS-PC.


 

Our most popular exotic material, Protopasta Carbon Fiber Composite HTPLA  is a combination of milled carbon fibers and high-performance PLA.

Resulting 3D prints made with our Carbon Fiber HTPLA are demonstrably more rigid, providing excellent structural strength and layer adhesion with very low warpage.

The embedded carbon provides a beautiful matte black finish with a slight sheen, resulting in 3D prints with exceptional accuracy, finish, and performance!

 

 

 

 

 

For exceptional accuracy, finish & performance, choose Carbon Fiber

Proto-pasta Carbon Fiber Composite HTPLA is a combination of milled carbon fibers and high-performance, heat treatable PLA (HTPLA). Resulting 3D printed prototypes and end-use parts are characterized by exceptionally stability of form and potential use up to 155 deg C (310 deg F) when heat treated.

Finish

Printed parts have a beautiful matte black finish with layer hiding sheen and texture. The carbon fibers give the surface a nice sheen and with layer heights under 0.1mm the layers blend into the texture and almost disappear.

Performance

Printed prototypes and end use parts using Protopasta Carbon Fiber HTPLA are characterized by exceptional stability of form and potential use up to 155 deg C (310 deg F) when heat treated. Carbon fiber's rigidity and hardness results in prints with improved form and function compared to standard HTPLA without carbon fibers. Excellent layer adhesion and minimal warpage (even without a heated bed) make this a great everyday filament for accurate parts. Increased rigidity from the carbon fiber means increased structural support but decreased flexibility, making our Carbon Fiber HTPLA an ideal material for frames, supports, shells, propellers, tools... really anything not expected (or desired) to bend. It is particularly loved by drone builders and and RC hobbyists.

Compatibility

Adaptable to most PLA-compatible printers. Heated bed recommended for process ease, quality, and reliability, but not required. Printer should allow 3rd party filament, parameter adjustment, and nozzle replacement. Specialized machine adaptation and maintenance may be required for Proto-pasta materials, particularly in continued use of abrasive materials. Some machines may require specific considerations for filament placement, path, adjustments, settings, or other preparation & maintenance.

Abrasive materials like Carbon Fiber and Metal Composites may cause premature wear of in line components such as bowden tubes, drive gears, nozzles, and other items in the filament travel path. Serviceable hardware including replaceable nozzles suggested. Wear resistant nozzles are recommended for extended use. Nozzles wear most quickly with flattening of the tip which affects nozzle diameter & distance to build plate. Inconsistent extrusion, inaccuracy & process instability. Extrusion width & first layer distance adjustments and/or replacement of nozzle. For more on nozzle replacement consider this blog demonstrating nozzle replacement & adjustments on a Prusa MK3. Reduce nozzle wear by minimizing over-extrusion & infill.

Finishing

Printed parts using Carbon Fiber HTPLA can be shaved/carved with a sharp blade for a smooth finish. Experiment with weathering or other painting techniques for a unique look. Also, expect improved bonding strength with glue compared to plastic without carbon fiber.

Carbon Fiber HTPLA is optimized for heat treating (also known as annealing or crystallizing) for higher temperature use. Heat treating creates a more crystalline molecular structure for maintaining stiffness to near melting, thus extending the useful range of HTPLA, but crystallization also creates shrinkage. HTPLA parts should be scaled in slicer to compensate for shrinkage when heat treating.

Additional post processes might inlcude sanding or painting. The addition of carbon fiber can lend well to ease of sanding and adhesion of coatings like paint, however, there are also additional safety considerations when generating dust through sanding and fumes through coating. Please seek safe practices with appropriate persona protective (PPE) and ventilation.

 

Getting Started with Proto-pasta PLAs including HTPLA

We've created this page to bring you a premium PLA and HTPLA printing experience that rivals our premium material. Follow below to improve your 3D printing experience. In other words, here's your shortcut to awesomeness with pasta. If at the end of this document you have questions or need assistance, please contact us at support@protoplant.com.

Filament Handling

Loose coils can be very tricky to manage. Going cowboy on your spool handling can quickly end up in a frustrating, tangled mess. Keep your loose coils wrangled with a spool holder like masterspool for a more trouble-free experience. Find out more about loose coil handling in Keith's blog post.

And for spooled filament, never let go of the loose end. When not in the printer extruder, tuck it away in the cardboard spool's corrugation! Also, avoid sharp bends and excessive force when loading filament into your printer.

Print settings

At Proto-pasta, we make high quality filament. We aspire to make exceptional results easy, but a positive result is very much dependent on your hardware, set-up, adjustments, and process parameters. Matching hardware with process and material for a positive experience is not always straight-forward, but you can start by pairing the following settings with your printer for a good starting point, then tune or troubleshoot as required.

Example settings for typical printer

  • Nozzle size = 0.4 mm (Standard to most printers & balances detail with productivity.)
  • Extrusion width = 0.45 mm (Typically larger than nozzle size. If using a larger nozzle diameter, be sure to set the extrusion width larger than that nozzle diameter.)
  • Layer thickness = 0.15 mm (For a balance of speed, quality & reliability.)
  • Speed(s) = 15-45 mm/s (Respecting mechanical and volume flow limits. Stay within the recommended speed range but apply slower speeds to the walls and faster speeds to the infill.)
  • Volume flow rate(s) = 1-3 cu mm/s (The result of above speed range, width, and layer thickness. Respect hardware and geometry limitations.)
  • Typical temperature = 215 C +/- 10 C (Matching material, hardware, and volume flow rate.)

Volume flow rate together with temperature dictates how melted the material is. This is hardware & condition dependent based on hot end, nozzle & extruder type, material & manufacturer as well as layer fan type, position & settings. Extrusion width, layer thickness & speed changes affect volume flow which may change required/desired temperature.

Additional settings of note

  • ‚ÄúGrid‚ÄĚ infill type at 20-30% - ‚Äúconnect infill lines‚ÄĚ unchecked (off).
  • Minimum 3 shells & 4 top/bottom layers for good surface quality.
  • Layer fan set to cool enough for build rate, but not so aggressive as to fail process by over-cooling nozzle and heater block.

Validation and fine-tuning

Post your prints & tag us @Proto_pasta on Twitter and Instagram. Need more help? Consider typical pitfalls and fixes below.

Typical pitfalls

  • Exceeding hardware capabilities.
  • Mismatch of flow rate and temperature.
  • Excessive nozzle cooling from layer fan yielding lower heater block and/or nozzle temperatures than set point.
  • Hardware shortcomings such as MK3 heat break, poor nozzle diameter, or other hangups.
  • Poor assembly or adjustment of components.
  • Excessive retraction distance or number of retractions.
  • Inaccurate flow with missing cross-sections or wall thickness not matching extrusion width software setting.

Typical Fixes

  • Heat break replacement with OEM, straight-through design and¬†defect-free, smooth bore.
  • Proper assembly of components without plastic oozing gaps & with thermal grease.
  • Lightly oiling filament, but careful, a little goes a long way.
  • Reducing layer fan speed and/or isolating from heater block and nozzle.
  • Installing heater block sock to isolate heater block & nozzle from layer fan.
  • Increasing temperature to flow past internal hang-ups.
  • Reduce speed and/or choose a single speed for a single¬†volume flow
  • Consider drive gear tension adjustment, bowden tube coupling/replacement, and spool mounting

We visited Joel and ended up with a helpful video on the subject:

NO MORE JAMS on the Prusa i3 mk3 3D Printer!

 

Carbon Fiber PLA

Carbon Fiber Reinforced PLA

Our most popular exotic material, prints made with our Carbon Fiber PLA are demonstrably more rigid, providing excellent structural strength and layer adhesion with very low warpage. It has a beautiful matte black finish with a slight sheen due to the embedded carbon.

What is it made out of?

Protopasta Carbon Fiber PLA is made from NatureWorks 4043D PLA Resin compounded with 15% (by weight) chopped Carbon Fibers. It is more brittle than standard PLA in its filament form, so handle it carefully to prevent breakage.
How much stronger is it?
The short answer is that this filament isn't "stronger," rather, it is more rigid. Increased rigidity from the carbon fiber means increased structural support but decreased flexibility, making our Carbon Fiber PLA an ideal material for frames, supports, shells, propellers, tools... really anything not expected (or desired) to bend. It is particularly loved by drone builders and and RC hobbyists.
Print Settings

Because of the chopped carbon, Protopasta Carbon Fiber PLA may have trouble getting through smaller nozzles. We have had good success using a .5mm nozzle and direct-drive spring loaded pinch-roll style extrusion head.Generally, our customers find it prints just like standard PLA on their machines (at around 195-210¬į F), though others find success running it a bit hotter (around 220¬į F). Experiment with your printer and see what works best for you.

Density:
1.3 g/cm3 (1300 kg/m3)Parameters:
Bed Temp (if available, is not required): 50¬į C
Hot End Temp: 195 ‚Äď 220¬į C

Carbon fiber and your printer nozzle

The carbon fibers in our filament are processed for an optimum size: short enough to print in PLA without clogging nozzles, but long enough to provide the added rigidity carbon fiber is famous for. At this length, the chopped carbon fiber makes this filament more abrasive than standard PLA. Prolonged use may result in more wear on your 3D printer, particularly lower-end nozzles.

 

 

 

Para uma correcta manutenção da sua impressora 3D, recomendamos sempre que trocar de material de filamento 3D,  a efectuar uma purga com filamento especial de limpeza.
Desta forma garante que não ficam vestígios de material nas paredes do nozzle, evitando o acumular de crosta que é criado sempre que efectua trocas de material.
Com este produto evita problema como "clogs" e "jams" e far√° com que o seu nozzle mantenha-se sempre limpo, durando muito mais tempo.
Poder√° encontrar a partir de 1.49‚ā¨¬† no seguinte LINK

 

Este  material é altamente abrasivo. Recomendamos a utilização de Nozzles de aço endurecido.

Poderá encontrar  no seguinte LINK

 

 

3D lac comprar em Portugal

Para obter maior aderência à superfície da sua  impressora 3D recomendamos a aplicar 3DLAC  na base da plataforma.

Poderá encontrar no seguinte LINK

 

 

Este material √© altamente higrosc√≥pico, absorvendo rapidamente a humidade do ar passados poucos minutos ap√≥s aberto, impossibilitando desta forma a correcta impress√£o 3D do mesmo. O resultado das impress√Ķes 3D de materiais com humidade tendem a ser fr√°geis e de acabamento irregular ou em certos casos, torna-se simplesmente imposs√≠veis de imprimir.
Dever√° de usar solu√ß√Ķes de caixas fechadas com dessecante como s√≠lica ou caixas pr√≥prias secadoras de filamento.
Poderá encontrar  no seguinte LINK

 

 

Download:
Technical and Safety Data Sheet

 

50g- Rolo
HTPLA Black ( Carbon Fiber Composite )
- Cor
1.75mm (+-0.05mm)
- Espessura / Toler√Ęncia de di√Ęmetro
F√°cil
- Facilidade de Impress√£o

We made some very unique filament at Proto-pasta!

Making Proto Pasta HTPLA v3 Highfive Blue 3D Printer filament!

QnA: How Proto-pasta makes filament!

HTPLA vs PLA and more with Proto-Pasta

Informação adicional

Peso 150 kg
Marca

ProtoPasta

Cor

Preto

Peso

Amostra, 50g

Di√Ęmetro do Filamento 3D

1.75 mm

Porquê comprar na Evolt?
Somos uma equipa jovem com sede em Aveiro e estamos profissionalmente na ind√ļstria da Impress√£o 3D h√° 8 anos. Estamos aqui para fazer uma parceria contigo e ajudar-te em todas as etapas da tua jornada. Estas s√£o algumas das vantagens que recebes como nosso cliente:
- Garantia de satisfação
Na Evolt investimos na tua satisfação e sucesso. Prestamos suporte gratuito e rápido por telefone, chat e email, tu e a tua satisfação são a nossa prioridade.
- N√£o consegues imprimir? Devolvemos o dinheiro.
√Č simples. Caso n√£o consigas imprimir ou n√£o gostes do filamento 3D devolvemos-te o dinheiro correspondente ao que ainda n√£o usaste. Sabe mais aqui.
- Envios r√°pidos
Loja Nacional com produtos em Portugal. Disponibilizamos de envios 24h para produtos "Recebe amanh√£".  Os pedidos realizados antes das 14h s√£o enviados no mesmo dia.
Tens alguma questão? Precisas de uma recomendação?
Contacta-nos!
A nossa miss√£o
Facilitar-te o acesso a produtos seleccionados com o rácio mais justo de qualidade/custo. Colocá-los ao teu dispor a um preço ainda melhor e tudo isto com stock em Portugal para que recebas os produtos o mais imediatamente possível
Links √ļteis
BlogTermos e Condi√ß√Ķes
Política de PrivacidadePolítica de CookiesRGPDResolução Alternativa de Litígios
Levantamento em m√£os
Dispomos da possibilidade de levantar gratuitamente encomendas na nossa loja.
O espaço físico (loja) encontra-se encerrado devido à pandemia e todas as compras de levantamento em loja têm que ser previamente feitas online. Obrigado pela compreensão!
Contactos
info@evolt.pt
Avenida de S√£o Mateus, n¬ļ 263
Murtosa 3870-059
Aveiro, Portugal
Socialização faz bem
‚̧ Evolt 
2021
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram