Aviso COVID-19: Est√£o a ocorrer atrasos por parte das transportadoras, podendo em certos casos o transporte 24h alargar-se para 72h+

HTPLA Amie's "Blood of My Enemies" Deep Translucent Red ( Community Inspired ) 500g - ProtoPasta

Em stock (pode ser encomendado sem stock)

40.34¬†‚ā¨

Em stock (pode ser encomendado sem stock)

Em stock (pode ser encomendado sem stock)

Envio:
Envio 24h
Prazo de entrega estimado para Portugal continental
Encomenda dentro de 8 horas 15 minutos (Até às 14:00) para receberes já a partir de amanhã
Garantia
2
14 dias
devolução
Pagamento
seguro
Descrição:

ProtoPasta é uma empresa situada nos Estados Unidos da América, de produção de filamentos para impressão 3D de alta qualidade.
Caracterizada pelos rolos feitos em cartão, esta marca é mundialmente famosa  por ser especializada em materiais como PLA e ABS modificados com outros materiais, como o PLA Magnético; o PLA Condutivo; PLA de fibra de carbono; HTPLA de cobre, latão ou bronze; ou o ABS-PC.


 

Amie's "Blood of My Enemies" is an original, one-of-a-kind, heat treatable dark red PLA(HTPLA ) filament inspired by filament workshop attendee Amie (@amiedoubled).

Utilizing atranslucent base, Blood of My Enemies finishes with a deep, blood red.

 

 

 

HEAT TREATING

Like our other HTPLAs, Glitter Flake Metallic Red PLA filament can be "Heat Treated" to increase crystallinity for "Higher Temperature" resistance compared to amorphous PLA, ABS, and co-polyesters like PETG! Glitter Flake HTPLA prints translucent, but turns opaque when heat treated (or crystallized). With a more crystalline structure, heat treated HTPLA parts can hold form to near melting, though temperatures where the material is practically useful vary greatly depending on geometry and load conditions!

For this improved performance, your prints should be baked in an oven until you see a change from translucent pink to opaque pink with reduced gloss. This visual change indicates the improved performance! We've seen the change take place in 5-10 minutes on thin walled parts but can take an hour or more. We've had good luck in a quality, at home convection oven at 110C (225F). Parts will get very "floppy" before becoming more firm, so please leave supports on your parts or support them and bake them on a flat, non-radiating surface (like glass, ceramic, or composite).

PRINTING

In our experience, good results were achieved using standard PLA parameters ranging from 195-225C nozzle with standard build surface preparation (blue tape, glue stick, or BuildTak). No heated bed required but up to 60C is okay. Beware, if the bed temperature is too high, your part base could actually heat treat while printing, increasing warping and decreasing adhesion. Some shrinkage will occur in the heat treating process, so dimension critical parts may need to be scaled appropriately (as much as 2.5% in our experience).

  • No abrasive fillers so expect normal wear with standard nozzles.
  • Available in 1.75 & 2.85 (3) mm diameter on a 500g diameter recyclable cardboard spool
  • Usable on most PLA-compatible printers, such as Lulzbot, Makerbot, FlashForge, Dremel, Ultimaker, Printrbot, and more!

 

High Temperature PLA ( HTPLA )

Looking for increased heat resistance without the need to switch to ABS? Protopasta¬†High Temperature PLA offers heat deflection of up to¬†88¬į C (190.4¬į F)¬†compared to standard PLA of 45-54¬į C (113-135¬į F). This makes it a great choice for moving parts (gears, RepRap pieces, etc) or prints that would face moderately high temperatures. Our High Temperature PLA is white, but can be painted after annealing.

What is it made out of?
Protopasta High Temperature PLA is made from a mineral filled, impact modified PLA with a nucleating agent to help promote crystallization. Crystallization after printing is what gives this material added heat resistance, so post-print annealing is essential to activate the heat deflection qualities of this material.How do I anneal my print?
You can anneal your finished prints several ways, the two easiest ways are by using hot (but not boiling) water or by placing it in a low temperature oven (newer oven models only). Follow these steps:
  • Water Method:¬†Find a pot large enough to hold your print and fill it halfway with water. On medium heat, heat the water until it reaches¬†95-115 C (200-240 F)¬†(a cooking thermometer works great for this), turn the heat to low and submerge the print in the warm water bath for 6-10 minutes. Placing a lid on your pot will help the water maintain temperature.
  • Oven Method:¬†Many newer ovens often have low temperature settings (sometimes called "keep warm" or "bread proof"). Set your oven to¬†95-115 C (200-240 F), place your finished print on a tray, and set it in the oven for 6-10 minutes.
  • SUPPORT YOUR PRINT! Because the annealing process will soften the plastic somewhat, it's best to support your print during this process.
What temperature should I print it at?
Because 3D printers vary so much from model to model, and because many RepRap printers combine parts from several manufactures, we can't provide the optimum temperature for your machine. Generally, our customers find it prints just like standard PLA on their machines (at around 210¬į C), though others find success running it a bit hotter (around 220¬į C).Do I need a heated bed?¬†No, High Temp PLA does not require a heated bed or an enclosure.

Getting Started with Proto-pasta PLAs including HTPLA

We've created this page to bring you a premium PLA and HTPLA printing experience that rivals our premium material. Follow below to improve your 3D printing experience. In other words, here's your shortcut to awesomeness with pasta. If at the end of this document you have questions or need assistance, please contact us at support@protoplant.com.

Filament Handling

Loose coils can be very tricky to manage. Going cowboy on your spool handling can quickly end up in a frustrating, tangled mess. Keep your loose coils wrangled with a spool holder like masterspool for a more trouble-free experience. Find out more about loose coil handling in Keith's blog post.

And for spooled filament, never let go of the loose end. When not in the printer extruder, tuck it away in the cardboard spool's corrugation! Also, avoid sharp bends and excessive force when loading filament into your printer.

Print settings

At Proto-pasta, we make high quality filament. We aspire to make exceptional results easy, but a positive result is very much dependent on your hardware, set-up, adjustments, and process parameters. Matching hardware with process and material for a positive experience is not always straight-forward, but you can start by pairing the following settings with your printer for a good starting point, then tune or troubleshoot as required.

Example settings for typical printer

  • Nozzle size = 0.4 mm (Standard to most printers & balances detail with productivity.)
  • Extrusion width = 0.45 mm (Typically larger than nozzle size. If using a larger nozzle diameter, be sure to set the extrusion width larger than that nozzle diameter.)
  • Layer thickness = 0.15 mm (For a balance of speed, quality & reliability.)
  • Speed(s) = 15-45 mm/s (Respecting mechanical and volume flow limits. Stay within the recommended speed range but apply slower speeds to the walls and faster speeds to the infill.)
  • Volume flow rate(s) = 1-3 cu mm/s (The result of above speed range, width, and layer thickness. Respect hardware and geometry limitations.)
  • Typical temperature = 215 C +/- 10 C (Matching material, hardware, and volume flow rate.)

Volume flow rate together with temperature dictates how melted the material is. This is hardware & condition dependent based on hot end, nozzle & extruder type, material & manufacturer as well as layer fan type, position & settings. Extrusion width, layer thickness & speed changes affect volume flow which may change required/desired temperature.

Additional settings of note

  • ‚ÄúGrid‚ÄĚ infill type at 20-30% - ‚Äúconnect infill lines‚ÄĚ unchecked (off).
  • Minimum 3 shells & 4 top/bottom layers for good surface quality.
  • Layer fan set to cool enough for build rate, but not so aggressive as to fail process by over-cooling nozzle and heater block.

Validation and fine-tuning

Post your prints & tag us @Proto_pasta on Twitter and Instagram. Need more help? Consider typical pitfalls and fixes below.

Typical pitfalls

  • Exceeding hardware capabilities.
  • Mismatch of flow rate and temperature.
  • Excessive nozzle cooling from layer fan yielding lower heater block and/or nozzle temperatures than set point.
  • Hardware shortcomings such as MK3 heat break, poor nozzle diameter, or other hangups.
  • Poor assembly or adjustment of components.
  • Excessive retraction distance or number of retractions.
  • Inaccurate flow with missing cross-sections or wall thickness not matching extrusion width software setting.

Typical Fixes

  • Heat break replacement with OEM, straight-through design and¬†defect-free, smooth bore.
  • Proper assembly of components without plastic oozing gaps & with thermal grease.
  • Lightly oiling filament, but careful, a little goes a long way.
  • Reducing layer fan speed and/or isolating from heater block and nozzle.
  • Installing heater block sock to isolate heater block & nozzle from layer fan.
  • Increasing temperature to flow past internal hang-ups.
  • Reduce speed and/or choose a single speed for a single¬†volume flow
  • Consider drive gear tension adjustment, bowden tube coupling/replacement, and spool mounting

We visited Joel and ended up with a helpful video on the subject:

 

Para uma correcta manutenção da sua impressora 3D, recomendamos sempre que trocar de material de filamento 3D,  a efectuar uma purga com filamento especial de limpeza.
Desta forma garante que não ficam vestígios de material nas paredes do nozzle, evitando o acumular de crosta que é criado sempre que efectua trocas de material.
Com este produto evita problema como "clogs" e "jams" e far√° com que o seu nozzle mantenha-se sempre limpo, durando muito mais tempo.
Poder√° encontrar a partir de 1.49‚ā¨¬† no seguinte LINK

 

 

3D lac comprar em Portugal

Para obter maior aderência à superfície da sua  impressora 3D recomendamos a aplicar 3DLAC  na base da plataforma.

Poderá encontrar no seguinte LINK

 

 

Este material √© altamente higrosc√≥pico, absorvendo rapidamente a humidade do ar passados poucos minutos ap√≥s aberto, impossibilitando desta forma a correcta impress√£o 3D do mesmo. O resultado das impress√Ķes 3D de materiais com humidade tendem a ser fr√°geis e de acabamento irregular ou em certos casos, torna-se simplesmente imposs√≠veis de imprimir.
Dever√° de usar solu√ß√Ķes de caixas fechadas com dessecante como s√≠lica ou caixas pr√≥prias secadoras de filamento.
Poderá encontrar  no seguinte LINK

 

 

Download:
Technical and Safety Data Sheet

 

500g- Rolo
HTPLA Amie's "Blood of My Enemies" Deep Translucent Red HTPLA ( Community Inspired )
- Cor
1.75mm (+-0.05mm)
- Espessura / Toler√Ęncia de di√Ęmetro
Muito F√°cil
- Facilidade de Impress√£o




Informação adicional

Peso 1100 kg
Marca

ProtoPasta

Cor

Vermelho, Transparente

Peso

500g

Di√Ęmetro do Filamento 3D

1.75 mm

Porquê comprar na Evolt?
Somos uma equipa jovem com sede em Aveiro e estamos profissionalmente na ind√ļstria da Impress√£o 3D h√° 8 anos. Estamos aqui para fazer uma parceria contigo e ajudar-te em todas as etapas da tua jornada. Estas s√£o algumas das vantagens que recebes como nosso cliente:
- Garantia de satisfação
Na Evolt investimos na tua satisfação e sucesso. Prestamos suporte gratuito e rápido por telefone, chat e email, tu e a tua satisfação são a nossa prioridade.
- N√£o consegues imprimir? Devolvemos o dinheiro.
√Č simples. Caso n√£o consigas imprimir ou n√£o gostes do filamento 3D devolvemos-te o dinheiro correspondente ao que ainda n√£o usaste. Sabe mais aqui.
- Envios r√°pidos
Loja Nacional com produtos em Portugal. Disponibilizamos de envios 24h para produtos "Recebe amanhã".  Os pedidos realizados antes das 14h são enviados no mesmo dia.
Tens alguma questão? Precisas de uma recomendação?
Contacta-nos!
A nossa miss√£o
Facilitar-te o acesso a produtos seleccionados com o rácio mais justo de qualidade/custo. Colocá-los ao teu dispor a um preço ainda melhor e tudo isto com stock em Portugal para que recebas os produtos o mais imediatamente possível
Links √ļteis
BlogTermos e Condi√ß√Ķes
Política de PrivacidadePolítica de CookiesRGPDResolução Alternativa de Litígios
Levantamento em m√£os
Dispomos da possibilidade de levantar gratuitamente encomendas na nossa loja.
O espaço físico (loja) encontra-se encerrado devido à pandemia e todas as compras de levantamento em loja têm que ser previamente feitas online. Obrigado pela compreensão!
Contactos
info@evolt.pt
Avenida de S√£o Mateus, n¬ļ 263
Murtosa 3870-059
Aveiro, Portugal
Socialização faz bem
‚̧ Evolt¬†
2021
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram